sony xplode 100w amp bridged push a 1600w cab


Problem with Sony Xplod XM-554ZR Car Audio Amplifier

 Will a sony xplode 100w amp bridged push a 1600w cab? if not what is the best compatible cabinet wattage reccomedation?
100watt amp and 1600 watt cab?? Your amp will run it but a lot of the dynnamics of the speakers won't be there.

Comments

Post a Comment

Popular posts from this blog

this is not possible

 after completing bvoc in automobile can i get mechanical design engineer post or automotive engineer or automation engineer. ChatGPT said: This is a very common and important question for B.Voc students. Let's explain it clearly: ❓ After B.Voc in Automobile, Can You Become: Career Role Can You Get It Directly After B.Voc? ✅ Technician / Service Advisor / Workshop Manager Yes – Easily ❌ Mechanical Design Engineer (CAD/CAE, SolidWorks, CATIA etc.) No – Not directly ❌ Automotive Engineer (R&D, Testing, Vehicle Design) No – Requires B.E./B.Tech ❌ Automation Engineer (Robotics, PLC, Mechatronics) No – Requires deeper technical/engineering study 🎓 Why Not These Engineering Jobs After B.Voc? Because: B.Voc is a skill-based practical degree , mainly focused on job-ready skills for service, repair, and basic management. Design, automation, or R&D jobs usually require deep engineering knowledge like: Engineering Mathematics Mechanics, Thermodynamics, Fluid M...
Read more

Torque settings mains big ends head

Image
 what are the torque settings for bearing mains,big ends and head cylinder bolts BIG END, MAINS AND CYLINDER HEAD TORQUE SETTINGS FOR 2.4 LITRE JEEP CHEROKEE 2003 MODEL Tighten the cylinder head bolts in the sequence shown. Using the 4 step torque turn method, tighten according to the following values: Step 1: All to  34 Nm (25 ft. lbs.) Step 2: All to  68 Nm (50 ft. lbs.) Step 3: All to  68 Nm (50 ft. lbs.) CAUTION:  Do not use a torque wrench for the following step. Step 4: Turn an additional  1/4 turn Step 5: Install and tighten bolts (1-10) in sequence shown, to  41 Nm (30 ft. lbs.)  . Tighten bolts (1-10) again to  41 Nm (30 ft. lbs.) PLUS 1/4 turn  in sequence shown. Install main bearing bedplate to engine block bolts (11-20), and torque each bolt to 28 Nm (20 ft. lbs.) in sequence shown. Connecting Rod Cap Bolts 54 Nm (40 ft. lbs.) + 1/4 turn 1997 Jetta: Torque settings..vw..the head, fly w...
Read more

remove the back wheel Schwinn Meridian

Image
Problem with Schwinn Meridian Adult 26-Inch 3-Wheel Bike How do I remove the How do I remove the back wheel to replace it due to its bent up;I removed to the outside nut and wheel wont come off ? Thank you for an intelligent answer and my problem was solved. I didn't have to remove the axle but knowing one wheel was round and the other was half moon I was able to remove it without damage . Now I can order another wheel and be riding. You will need to remove the two bolts and nuts/washers that hold the wheel axle in place. After that you can pull the wheel off the frame with a little force. See the image below where two bolts that hold axle on both side are. The bolts are square near the end and will go into a square hole or cut out in the bike-frame  Putting these bolts on is a bit difficult at first, but once you have done it, its basically easy. For the rear wheels, the right side axle is shaped like a "D" (not ...
Read more