Over heating white smoke out tail pipe

Over heating white smoke out tail pipe when car first starts



 Not leaking any coolent but overheat reg also no heat in car blows white smoke when you frist start.


Ok it could be a couple things check and/or change the thermostat if that doesnt work then try to replace the heater core

Comments

Post a Comment

Popular posts from this blog

Laptop Fan Not Working? Here’s How to Fix It!

 How to Fix a Laptop Fan That Stopped Working A non-working laptop fan can lead to overheating, sudden shutdowns, and even hardware damage . If you notice that your laptop feels too hot or is shutting down unexpectedly, your fan might not be working. In this guide, we’ll go through step-by-step solutions to fix a stuck, broken, or unresponsive laptop fan . 1. Check If the Fan Is Spinning ✔ Place your hand near the laptop’s air vents and see if you feel airflow. ✔ Listen for fan noise —if it’s completely silent, the fan might be stuck. ✔ If the laptop overheats and shuts down , it’s likely a fan issue. 🛑 If your fan is not spinning at all, move to the next steps. 2. Restart Your Laptop & Enter BIOS Sometimes, the fan is disabled due to firmware issues. ✔ Restart your laptop and enter BIOS/UEFI (Press F2, F10, or DEL while booting). ✔ Look for Fan Control Settings and ensure the fan is enabled . ✔ Save changes and restart your laptop. 3. Clean Dust from the...
Read more

Torque settings mains big ends head

Image
 what are the torque settings for bearing mains,big ends and head cylinder bolts BIG END, MAINS AND CYLINDER HEAD TORQUE SETTINGS FOR 2.4 LITRE JEEP CHEROKEE 2003 MODEL Tighten the cylinder head bolts in the sequence shown. Using the 4 step torque turn method, tighten according to the following values: Step 1: All to  34 Nm (25 ft. lbs.) Step 2: All to  68 Nm (50 ft. lbs.) Step 3: All to  68 Nm (50 ft. lbs.) CAUTION:  Do not use a torque wrench for the following step. Step 4: Turn an additional  1/4 turn Step 5: Install and tighten bolts (1-10) in sequence shown, to  41 Nm (30 ft. lbs.)  . Tighten bolts (1-10) again to  41 Nm (30 ft. lbs.) PLUS 1/4 turn  in sequence shown. Install main bearing bedplate to engine block bolts (11-20), and torque each bolt to 28 Nm (20 ft. lbs.) in sequence shown. Connecting Rod Cap Bolts 54 Nm (40 ft. lbs.) + 1/4 turn 1997 Jetta: Torque settings..vw..the head, fly w...
Read more

Troubleshooting and Repairing the Acer Predator Helios 300: A Comprehensive Guide

Image
  Step-by-Step Guide to Disassemble the Acer Predator Helios 300 Laptop The Acer Predator Helios 300 is a popular gaming laptop known for its powerful hardware and sleek design. However, like any electronic device, it may require disassembly for upgrades, repairs, or cleaning. This guide will walk you through the process of disassembling the Acer Predator Helios 300 in detail, ensuring you can safely and effectively take apart your laptop. ACER PREDATOR GAMING LAPTOP Welcome to LAPTOFIX  Laptop and Printer Repair Center! We specialize in  fast, affordable laptop and printer repairs . From  hardware fixes  and  virus removal  to  printer setup  and  data recovery , our expert technicians are here to solve all your tech problems. We offer  same-day service ,  on-site repairs , and  free diagnostics  to make the process easy and stress-free. Serving THANE & MUMBAI, we pride ourselves on reliable, customer-focused ser...
Read more