solutionsforeverything

 Keurig  coffee maker Troubleshooting: The problem with the touchscreen not responding, is caused by dirt/coffee residue, getting under the bezel around the screen. Sometimes a tissue soaked in Windex, then polished with a dry one , will temporarily remedy this. The only permanent fix is to disassemble the head, remove the lcd screen and clean it thoroughly, as well as under the bezel. If your Keurig 2.0 display is blank, try unplugging the brewer and plugging it back on. See if the issue is resolved. If your Keurig 2.0 touch screen is still cold towards you, get ready for some troubleshooting. Step 1: Plug in your Keurig 2.0. The power icon should be at the bottom left of the display.  If nothing shows, follow our section ‘My Keurig Won’t Turn On’. If you can see the Power button, turn it on and proceed to Step 2. Step 2: Go to “Menu” and proceed to set the clock. Step 3: Navigate yourself through the “Menu” and try to set all the menu options. Step 4: When you reach the...

 Igloo ice maker icefull light stays on If the igloo ice maker icefull light stays on, that means  The hard water had covered the infrared source and/or receiver. They are opposing black and transparent 3mm circles on the left and right wall when you look inside your icemaker. They are supposed to detect if ice cubes pile up so high that they disrupt the direct liner of view between those 2 dots. Just clean them with a wet acidic solution to clean of the hardness, e.g. use vinegar or lemon juice.This process will help to get icefull light off. Also you can try this simple trick if the above process is not helping 1. turn machine on . 2. press the select button for 10 sec. then 3. press the power button for 10 sec. and then turn off the machine and unplug it for 6 hours. I included some links for your convenience. Good Luck 1 How to fix portable ice machine part 1 of 3 Troubleshooting Portable Ice Makers Igloo ICE102 WHITE User Manual Troubleshooting Guide Make sure the small e...

TOYOTA TACOMA FUSE BOX  EFI fuse under the hood Toyota Tacoma (2005 – 2008) – fuse box diagram Year of production: 2005, 2006, 2007, 2008 Engine compartment Toyota Tacoma mk2 – fuse box – engine compartment Instrument panel Toyota Tacoma mk2 – fuse box – instrument panel Fuses (type A) Fuse Ampere rating [A] Circuit 1 A/C 10 Air conditioning system 2 FR FOG 15 Front fog lights 3 TOWING TAIL 30 Trailer lights (tail lights) 4 STOP 10 Stop lights, high mounted stop light, vehicle stability control system, anti- lock brake system, shift lock system, multiport fuel injection system/ sequential multiport fuel injection system, towing converter 5 OBD 7,5 On- board diagnosis system 6 EFI NO.2 10 Multiport fuel injection system/sequential multiport fuel injection system 7 TOWING BRK 30 Trailer brake controller 8 BATT CHG 30 Trailer sub battery 9 TOWING 30 Towing converter 10 TRN- HAZ 15 Turn signal lights, emergency flashers, meter and gauge 11 R...

 Where is fuse box located in honda Fuses, located in-between the battery, are the electrical components your car draws power from. It's important to know where the fuses are located and what each fuse does, so that if you ever have a problem you know where to start looking. Always start the diagnosis of an electrical problem with its fuse because they are easy to test and pretty cheap to replace. Honda  Component Breakdown Interior Fuse Box The interior fuse box is located underneath the dashboard on the driver's side. The lid is clipped in. To remove it, swing the lid down and pull it out. Interior Fuse Box Driver's side fuse box. The interior fuse panel (Figure 1a) is located under the dash (Figure 1b). The table in Figure 1c contains the fuse, the rating, and what the fuse does. For example, if your radio stopped working, you'd need to test fuse number 23 and replace it with a new 15 amp fuse if found to be faulty. Because interior fuses commonly fail, it is recomme...

Location of engine vin serial number The vehicle identification number (VIN) is located on the left side rear of the engine block (1) and is typically a nine digit number stamped or laser-etched onto the engine at the vehicle assembly plant. •The first digit identifies the division. •The second digit identifies the model year. •The third digit identifies the assembly plant. •The fourth through ninth digits are the last six digits of the VIN.  engine vin number location

Coolant Leaking Behind Waterpump 95 mustang v6 leaking coolant behind the new water pump. worse when turned on. does not appear to be the pump or any hoses. Solution: If the leak is behind the water pump , then either the new water pump gasket is leaking or the timing cover from the timing chain that the water pump bolts to is leaking and the gasket between the timing cover and the engine block. A couple of the water pump bolts are actually studs that go through the timing cover to the engine block. When the nuts are loosened, the timing cover also loosens. If the gasket for the timing cover is close to failing, it will start to leak. The reason it doesn't leak much with the engine off it because the water pump is not running and no real pressure is on the system. When the engine is running, the cooling system builds up pressure, usually 16 psi and it will push through a weak gasket. I think it is just in need of a new gasket at 151000 miles. The bolts will ...

Water Pump Leak Repair I have a problem with a water pump leak. I have replaced the original with a new pump, but I still have a leak I suspect around the gasket between the waterpump and the engine block. Any suggestions? I was very careful to clean the surfaces and evenly tighten the six bolts in a rotation first finger tight, then to 11 ft-lb, and finally to 22 ft-lb. Is 22 ft-lb the right final torque or do I need to re-torque after the engine has been through a couple of temperature cycles? Solution: I would check the intake gasket for leaking and running down,looking like its the waterpump, as far as I can tell you are doing everything right ,if need be I would put a pressure tester on the cooling system and pump it to 20 lbs and looking very closely at the intake. all I can suggest is to put a little sealant on the bolts,11ft lbs the first pass and 22 ft lbs final pass is the correct specs.no I wouldnt torque it to 28 ft lbs as you are asking ,.let me ask this...