Sony Xplod XM-554ZR Car Audio Amplifier Sub-woofer not working

SUB WOOFER NOT WORKING LIKE ORIGINAL


Problem with Sony Xplod XM-554ZR Car Audio Amplifier

10 inch subs need help

I have 10 inch subs in my car i don't know why but they wont really hit like if you turn the amp all the way up and stuff it vibrates a little bit just not like real subs should like it dont bounce the part its supposed to what is the problem i know the amp is very strong but why would it not still make them bounce????


It sounds like the wiring either to the amp or to the subs is put together wrong. This can be because you have them setup in stereo but have the sub on bridge mode or vica versa. This can also be from how you ran the audio input wither from speakers or rca..either wired wrong or the switch for the two options is wrong. Also make sure your gain is turned up. Sound also depends on what kind of box it is in. It HAS to be in a box.

set FM channels on Sony Xplod XM-554ZR Car Audio Amplifier

Problem with Sony Xplod XM-554ZR Car Audio Amplifier
How to set FM channels in d system ,i hav a sony xplod cassette stereo...plzzz help

GO TO 

Http://www.xplodsony.com/support for info on all sony items

Sony Xplod XM-554ZR Car Audio Amplifier Installation

Problem with Sony Xplod XM-554ZR Car Audio Amplifier

How do i intall my amp?

I have a xplode 600w amp how do i install it to my speakers and cd player step by step

First you need to run a power cable for the battery to where ever you are going to place the amp DO NOT hook the cable to the battery until the very last just wire it to the amp for now.next you will want to ground your amp hook the ground wire to the amp and the other end to a solid piece of metal in the car this is very important if you don't get good metal on metal contact you'll blow a fuse. If you can hide it well strip back a bit of carpeting and use sand paper to remove all paint from the metal and drill a hole for a screw. once that is finished you will need to run a remote wire from the amp to the car stereo usually these are the blue wire on the harness in the dash. once that is hooked up run the rca cables (reds and whites) plug in to amp and then in to back of cd player. once this is all hooked up and fully secure hook the power cable to the battery make good contact and if everything is grounded right you should get the lights on in the amp. Next step hook up the speakers run speaker wire from the amp to your speakers make sure negative goes to negative and positive to positive .

Sony Xplod XM-554ZR Car Audio Amplifier Wiring problem

Problem with Sony Xplod XM-554ZR Car Audio Amplifier

Wiring problem

The power wires details for  sony xplod head unit model is cdx-gt260

Power wires are as follows -

Red = Switched power (ACC)

Yellow = Constant power

Black = Ground

Sony Xplod-XM-554ZR Amplifier circuit board resistor

Problem with Sony Xplod XM-554ZR Car Audio Amplifier

Sony Xplod-XM-554ZR-- - - Resistor on circuit board HELP!!!

Well my brothers amp on his car just quit working. Me being an EE student i go ahead and open up to see whats inside. Unscrew everything and turn the board over to find a "open" surface mount resistor. I would like to find out what the value is for this "R466" (around in the middle of the board). This resistor burnt up, so basically it is unidentifiable. Possible values but not sure could be 2R1 which is 2.1 Ohms or, could be 221 which equals 220 Ohms. Can anyone please tell me the value or numbers on the top of this resistor, i would greatly appreaciate it. AGAIN the resistor is R466 around the middle of the board.

R466 is chip resistor 220 Ohms 1/8 watt connecting between Emitter pins of Q408 and Q409.

Its part number is ...

R466 "1-216-182-00" RES-CHIP 220 5% 1/8W

Available in Part Store.

Sony Xplod amp will not get off of power protection mode

Problem with Sony Xplod XM-554ZR Car Audio Amplifier

Xplod amp will not get off of power protection mode

Yesterday my Sony xplod 600w xm554ZR amplifiers power protection light had come on and it wont work now. I have checked all of the fuses and they are in mint condition, the amplifier was not even warm. I had disconnected all of my wiring and re connected it all, but none of this has seemed to work. Any ideas for a solution for this problem please let me know.

If the protect light stays on the amp is blown or has flawed components and is only repairable by expirenced sony tech

1000 watt sony XPLOD amp LED turns RED

Problem with Sony Xplod XM-554ZR Car Audio Amplifier

I have 1000 watt sony XPLOD amp and i just

I have 1000 watt sony XPLOD amp and i just installed it today. with new monster cable&ground. the green light turns on& thumping goes for a little. i try to raise up just a little bit& after 2 thumps my amp light turns red.. whats happening??

===========

I think if I'm correct you are running to many speakers and have your ohm load to low for the amp causing it to go into protection. 1 single voice coil speaker equals 4 ohms for every speaker you have divide 4 ohms by number of speakers (ie. 2 single voice coil speakers equals 2 ohms or 1 dual voice coil speaker equals 2 ohms) this is for parallel wiring. For series wiring do the opposite if you have 2 speakers you are running an ohm load of 8 ohms the same for a dual voice coil ran in series. Series is positive on the amp to positive on hook up A negative of hook up A to positive of hook up B negative of hook up B to negative on the amp.

OR

It isn't getting enough power and its tripping the internal switch on the amp and putting it in safe mode. either your wire isn't a high enough gauge. you might need a capacitor or you need bigger wire.